Skip to navigation

BBC Micro Elite

Dashboard: DIALS (Part 3 of 4)

Name: DIALS (Part 3 of 4) [View in context] Type: Subroutine Category: Dashboard Summary: Update the dashboard: four energy banks
This and the next section only run once every four iterations of the main loop, so while the speed, pitch and roll indicators update every iteration, the other indicators update less often.
LDA MCNT \ Fetch the main loop counter and calculate MCNT mod 4, AND #3 \ jumping to rT9 if it is non-zero. rT9 contains an RTS, BNE rT9 \ so the following code only runs every 4 iterations of \ the main loop, otherwise we return from the subroutine LDY #0 \ Set Y = 0, for use in various places below JSR PZW \ Call PZW to set A to the colour for dangerous values \ and X to the colour for safe values STX K \ Set K (the colour we should show for high values) to X \ (the colour to use for safe values) STA K+1 \ Set K+1 (the colour we should show for low values) to \ A (the colour to use for dangerous values) \ The above sets the following indicators to show red \ for low values and yellow/white for high values, which \ we use not only for the energy banks, but also for the \ shield levels and current fuel LDX #3 \ Set up a counter in X so we can zero the four bytes at \ XX12, so we can then calculate each of the four energy \ banks' values before drawing them later STX T1 \ Set T1 to 3, the threshold at which we change the \ indicator's colour .DLL23 STY XX12,X \ Set the X-th byte of XX12 to 0 DEX \ Decrement the counter BPL DLL23 \ Loop back for the next byte until the four bytes at \ XX12 are all zeroed LDX #3 \ Set up a counter in X to loop through the 4 energy \ bank indicators, so we can calculate each of the four \ energy banks' values and store them in XX12 LDA ENERGY \ Set A = Q = ENERGY / 4, so they are both now in the LSR A \ range 0-63 (so that's a maximum of 16 in each of the LSR A \ banks, and a maximum of 15 in the top bank) STA Q \ Set Q to A, so we can use Q to hold the remaining \ energy as we work our way through each bank, from the \ full ones at the bottom to the empty ones at the top .DLL24 SEC \ Set A = A - 16 to reduce the energy count by a full SBC #16 \ bank BCC DLL26 \ If the C flag is clear then A < 16, so this bank is \ not full to the brim, and is therefore the last one \ with any energy in it, so jump to DLL26 STA Q \ This bank is full, so update Q with the energy of the \ remaining banks LDA #16 \ Store this bank's level in XX12 as 16, as it is full, STA XX12,X \ with XX12+3 for the bottom bank and XX12+0 for the top LDA Q \ Set A to the remaining energy level again DEX \ Decrement X to point to the next bank, i.e. the one \ above the bank we just processed BPL DLL24 \ Loop back to DLL24 until we have either processed all \ four banks, or jumped out early to DLL26 if the top \ banks have no charge BMI DLL9 \ Jump to DLL9 as we have processed all four banks (this \ BMI is effectively a JMP as A will never be positive) .DLL26 LDA Q \ If we get here then the bank we just checked is not STA XX12,X \ fully charged, so store its value in XX12 (using Q, \ which contains the energy of the remaining banks - \ i.e. this one) \ Now that we have the four energy bank values in XX12, \ we can draw them, starting with the top bank in XX12 \ and looping down to the bottom bank in XX12+3, using Y \ as a loop counter, which was set to 0 above .DLL9 LDA XX12,Y \ Fetch the value of the Y-th indicator, starting from \ the top STY P \ Store the indicator number in P for retrieval later JSR DIL \ Draw the energy bank using a range of 0-15, and \ increment SC to point to the next indicator (the \ next energy bank down) LDY P \ Restore the indicator number into Y INY \ Increment the indicator number CPY #4 \ Check to see if we have drawn the last energy bank BNE DLL9 \ Loop back to DLL9 if we have more banks to draw, \ otherwise we are done